Europa Clipper Scale Model version 2025D by ddThingz on Thingiverse: https://www.thingiverse.com/thing:4903128

Summary:
Europa Clipper Model version 2025D

This is a model for anyone who might wish to see Europa Clipper's major components with all its science instruments, and manipulate the solar-array-radar wings. The model very roughly emulates the mechanical freedom of the solar-array to rotate, which is of course less than 360 degrees.

The spacecraft's X, Y and Z body axes are plainly marked on the model. VSCA marked on the model and its stand indicates the Spacecraft's Velocity vector during Standard Closest Approach at Europa. The following Engineering Components are identifiable on the model:

High-Gain Antenna HGA 
Radome Sun Shield 
Medium Gain Antenna 
Three Fan-Beam Antennas 
Three Low-Gain Antennas 
Plume Shield for ECM (effective prior to ECM deployment)
Four Rocket-Engine Modules, each with six nozzles Four 
Reaction Wheels 
Two Stellar-Reference Units 
Two pairs of Sun Sensors 
Main Thermal Radiator 
Two Solar Array wings t
he Propulsion module, too, of course. 

And the Science Instruments:

ECM: three sensors on boom, Europa Clipper Magnetometer 
Four PIMS apertures, Plasma Instrument for Magnetic Sounding
SUDA aperture, Surface Dust mass Analyzer
MASPEX aperture, Mass Spectrometer for Planetary Exploration Europa
Two apertures for EIS, Europa Imaging System: the Narrow-Angle Camera, and the smaller Wide-Angle Camera 
MISE aperture, Mapping ImagingSpectrometer for Europa, plus its adjacent thermal radiator
Two UVS apertures, Ultraviolet Spectrograph for Europa 
ETHEMIS aperture, Europa Thermal Emission Imaging System 
Six REASON dipole antenna pairs on the wings, Radar for Europa Assessment and Sounding, Ocean-to Near surface; the long ones are HF antennas, and the shorter ones are VHF.

Not included (to enable easy printing and assembly) are the spacecraft's eight pairs of struts that supported the folded solar panels through launch and separation from the Falcon Heavy's upper stage. Note: on the spacecraft, there is no mechanical axle joining the Solar Arrays; that's just a model contrivance.

To identify the instruments and spacecraft components, refer to the NASA website, and this rotating view of the spacecraft.

Printing: All the model's components are designed to be simple enough for FDM (note 1) flat-bed printing, so you can just carry the three .stl files to your nearby desktop 3D printer's "slicing" software, and use its default settings without any rafts or support material required.

Scale: If printed as-is with no size adjustment, the scale is approximately 1:106. While the scale is not exact, this version successfully reproduces key visual cues and technical details. Enlargements have been successfully printed (look on thingiverse.com for Thing #5320315, the robust 1:30-ish version).

Solar Array Wings: Add some maroon-colored tape, or glue on the solar-cell images provided, to represent the photovoltaic solar cells. There's an optional high-quality metallic foil-based solar-array sticker available for purchase from a third party. Each sticker measures 132 mm x 48 mm. To see it, go to JukeboxPrint.com and request a quote based on the "Order number 4710047" design.

Snip off the REASON VHF antennas, remove their sprues, and press each one onto its connector on the panel edges, perpendicular to the panels (see images). Glue in place. Add the longer REASON HF antennas (see photos), one on each wing. If they stay in place without glue, you can easily print and replace broken ones if necessary later on. 

IMPORTANT: Use an emory board to smooth the +X Wing connector rod to ensure smooth rotation; then when inserting through the Body, observe "+X" markings on the Wing and on the Body, and orient them as shown in the "front page" picture (to ensure proper engagement of the mechanical stop). Snap to join the two wings through the Body. Then apply thin glue to the joint, while supporting the model in a way that will not let glue drip into the rotating sleeve.

Version 2025D: This Version includes features and refinements that make it a lot easier to assemble. For example, the Solar Array Wings snap together and align much better. Also, the Solar Array now incorporates a mechanical stop. Positioning of the minus-Z PIMS instrument is corrected. To contend with the constraints of FDM printing, a new "+Z Panel" has been added, better representing the Stellar Reference Units, and the SUDA and MASPEX instruments. (Previously the SRU print-supports could easily be confused with the apertures). Finally, this version collects all the parts into three files: the Body, the Wings, and the Stand.

Note 1: FDM: Fused Deposition Modeling, one of the most common desktop 3D printers these days. It's also called FFF, Fused Filament Fabrication.

This Europa Clipper Scale Model is dedicated to the memory of Hirai Isao, the master of accurate spacecraft scale modeling. Hirai-san operated the Scale Model Company in Hawthorne, California from 1967 until his passing in 2024.
